Mercedes CLA EV Battery: 85 kWh and 58 kWh Pack Analysis

The electric Mercedes CLA is the first production car on the Mercedes Modular Architecture (MMA) and the company’s first 800V volume model. We covered the pack hardware when Mercedes first showed it in our Mercedes MMA Battery post: 192 prismatic cells in four 48-cell modules, a steel frame with an aluminium tray and cooling bonded into the floor. This post picks up from there with the production car. It is a pack analysis rather than a teardown, as we have not found a published dismantling, so it works from Mercedes’ own figures and images, press and road-test reports, and our Pack Database.

Headline numbers

  • 85 kWh usable, NMC with a silicon oxide and graphite anode [1]. The US certification filing declares 700 V nominal, 127 Ah and 179 Wh/kg [14], which gives 88.9 kWh total (700 V x 127 Ah) and a usable window of 96%.
  • 58 kWh usable, LFP [1]: about 120 Wh/kg (58 kWh over 484 kg, our arithmetic; total energy has not been published, so this is on a usable basis).
  • Pack masses of 496 kg (NMC) and 484 kg (LFP) from Mercedes’ own technical graphic [13]. As a cross-check, 179 Wh/kg x 496 kg is 88.8 kWh, which agrees with the 88.9 kWh above (our arithmetic).
  • 192 cells in series in both packs [2][10]. For NMC, 700 V over 192 cells is 3.65 V per cell; for LFP we estimate 614 V (192 x 3.2 V).
  • Peak DC charging of 320 kW (85 kWh), 250 kW (71 kWh) and 200 kW (58 kWh) [3][4][5].
  • Packs assembled at the Mercedes plant in Kamenz, Germany [1][2].
Mercedes graphic summarising the MMA battery: liquid cooling, four modules, cell energy density of 680 Wh/l for NMC and 450 Wh/l for LFP, usable energy of 85 and 58 kWh, and masses of 496 and 484 kg.
Mercedes’ summary of the two MMA packs, including the pack masses. Image: Mercedes-Benz

Four variants, one pack

VariantChemistryUsable energy (kWh)Peak DC (kW)10 to 80% (min)WLTP range (km)
CLA 200LFP5820020542
CLA 250NMC7125020674
CLA 250+NMC8532022792
CLA 350 4MATICNMC8532022771
Electric CLA saloon variants. Sources: CLA 250+ and 350 4MATIC [3]; CLA 200 [4][5]; CLA 250 [5][11].

What stands out is how little changes between the variants. The two packs are close in mass [13] and Mercedes said they are the same size [2], and the 71 kWh CLA 250 is reported to use the 85 kWh hardware with the usable window reduced in software [6]. Our arithmetic on cell volume supports the single-envelope idea. At the 680 Wh/l Mercedes quotes for the NMC cells [1], 88.9 kWh of cells takes about 131 litres. At 450 Wh/l for LFP [1], 58 to 60 kWh of cells takes 129 to 133 litres. Our reading is that both chemistries fill the same cell volume, which is what you would expect from one module design and one tray carrying two cells of the same can size.

The 71 kWh car uses 80% of the 88.9 kWh total, against 96% for the 85 kWh versions. The customer carries the full cell mass and the factory pays for the full cell content, but the plant builds one pack instead of two.

Nigel: Capping the pack in software is an easy fix and nothing new. Engine makers have offered power variants for years by changing the calibration in the control system. Running the cells in a narrower window will also help the lifetime of the pack, and so should reduce the warranty cost for this model.

Cells

  • Supplier: CATL supplies both cell types at launch. The NMC cells are confirmed as CATL prismatic cells [9]. A 2023 report had named BYD for the LFP cells, and our MMA post has been corrected.
  • NMC: silicon oxide blended into the graphite anode, with Mercedes claiming up to 20% higher gravimetric energy density than the previous graphite-anode generation and 680 Wh/l at cell level [1]. The silicon share is not disclosed; the head of battery systems would only say it is below 50% [2].
  • LFP: 450 Wh/l at cell level [1].
  • Format: prismatic hard-case cells [1], 24 side by side in each module [2].
  • Cell capacity: with all 192 cells in series, the declared 127 Ah pack capacity [14] is also the NMC cell capacity, so each cell holds about 463 Wh (127 Ah x 3.65 V). For LFP (our estimate), 58 kWh over 192 cells is 302 Wh usable per cell, so at least 94 Ah at 3.2 V, which points to a cell of roughly 100 Ah. From the press images we estimate the can at about 32 x 275 x 78 mm (see Pack and cell size from the press images).
  • Second source: Samsung SDI has signed a multi-year supply deal for high-nickel NMC cells, reported to be for MMA vehicles from 2028 [9].

See our NMC and LFP pages for the chemistry background.

Charging

The 85 kWh pack peaks at 320 kW [3]. At roughly 700 to 750 V that is about 430 to 460 A, which is why an 800V pack is needed: at around 500 A on a CCS cable, a 400V pack tops out near 200 kW. That is our arithmetic, not a Mercedes figure.

Mercedes gives two points on the curve. Up to 36 kWh goes in during the first ten minutes [1], and 59.5 kWh goes in from 10 to 80% in 22 minutes [3]. That is an average of about 216 kW (2.5C) for the first ten minutes, then about 118 kW (1.4C) for the remaining 23.5 kWh over 12 minutes. An electrive road test fills in the shape: a highest reading of 305 kW, just under 200 kW at 50%, about 160 kW at 60% and under 100 kW at 80%, with 10 to 30% taking just under 5 minutes and 60 to 80% about 9 minutes [12].

We drew one curve that matches all of these points. It is an estimate, not a measurement: many curves could pass through the same figures, but they would all share the same broad shape.

Two charts for the Mercedes CLA 85 kWh pack. Left: estimated charge power against state of charge, peaking at about 305 kW near 12%, holding about 200 kW to 50% and falling to about 90 kW at 80%, with road-test readings and Mercedes-derived averages marked. Right: estimated energy added against time, reaching 36 kWh at 10 minutes and 59.5 kWh at about 22 minutes.
Our estimated 10 to 80% charging curve for the 85 kWh pack, drawn to match Mercedes’ figures [1][3] and electrive road-test readings [12]. Not a measured curve.

The LFP pack is gentler at the peak but holds its rate better. 200 kW on 58 kWh is 3.4C, and 10 to 80% (40.6 kWh) in 20 minutes [4] is an average of 122 kW, or 2.1C, against 1.9C for the NMC pack. That fits the flatter charge acceptance of LFP. Our arithmetic; we have found no road-test curve for the LFP car.

Natural taper or thermal limit?

On a graphite-based anode, the usual limit on charge current is lithium plating. As the anode fills, its potential against lithium falls, and the current it can take without plating falls with it. The result is a charge map where the allowed current drops steadily with state of charge, and drops further when the cells are cold. A thermal limit looks different: it depends on how hot the pack has become, so it tends to show as a step or a cap that moves from session to session rather than following state of charge.

The CLA curve has the first shape. After a brief peak it holds about 200 kW to 50%, then falls roughly in a straight line, about 3.5 kW for every percent of state of charge, to below 100 kW at 80%. The one direct clue on temperature comes from the road test: on the approach to a charger the car displayed its charge power as limited by temperature, rising to 220 kW as preconditioning finished [12]. That is the cold side of the map. Our reading is that the taper is mainly the state-of-charge limit expected from the anode, with temperature setting how much of it is available. The pack is cooled and heated only through its underside, via the cooling plate integrated into the housing base [2][13], so a hot-side limit is plausible too, but nothing published shows one.

Nigel: The only way to separate the two is to observe charging from different starting temperatures.

A simple way to do that on a customer car: charge from the same 10% start at three preconditioned pack temperatures, then repeat with two charges back to back. If the knee in the curve moves to a lower state of charge when the pack is colder, that is the plating limit. If a hot start or the second session cuts power at the same state of charge, that is a thermal limit. See our fast charging and battery cooling options pages.

400V charging

European launch cars had no DC/DC booster, so they could not use 400V DC chargers at all [7]. Mercedes then confirmed a converter for US cars so they could use the 400V Supercharger network [8]. Leaving the booster out saves mass, cost and conversion losses, which fits a car designed around efficiency, but it limits where the car can charge. It is a clear example of the trade-off covered on our 800V architecture page.

Pack construction

The mechanical layout is covered in our MMA post. Mercedes’ labelled exploded view and the production press images add the following.

Labelled exploded view of the Mercedes MMA battery: housing cover with gas ducts, insulating inserts, low-voltage wiring harness, four cell modules with cell monitoring units, electrics and electronics at the rear, and the housing underside with integrated cooling plate and a cast cross brace.
The MMA battery exploded, from the cover with its gas ducts down to the housing base with its integrated cooling plate and cast cross brace. Image: Mercedes-Benz
  • Layers: housing cover with gas ducts, insulating inserts, low-voltage wiring harness, four cell modules each with a cell monitoring unit, the electrics and electronics at the rear, and the housing underside with an integrated cooling plate [13].
  • Cross brace: a cast aluminium brace runs across the centre of the housing, between the front and rear pairs of modules. It stiffens the tray across the car and gives the lid a central fixing line.
  • HV cable routing: the high-voltage cable that links the front of the car to the rear electronics runs in a recess down the centre of the lid, so it adds nothing to the height of the car floor.
  • Mixed construction: Mercedes described the pack as a mixture of cell-to-module and cell-to-pack: modules are bonded in, but the cover is bolted and modules, harness and connectors can be replaced individually [2].
  • Safety: the housing is part of the crash structure, Mercedes adds its own pole impact and underbody touchdown tests, and a sensor in the pack monitors it while the car is parked [1].
  • Warranty: 70% capacity for 8 years or 160,000 km [3].
Mercedes MMA battery pack with the cover fitted, showing the recessed channel down the centre of the lid where the high-voltage cable runs.
The pack lid, with the recessed channel down its centre for the high-voltage cable. Image: Mercedes-Benz

Modules

Each module holds 48 cells, 24 side by side [2]. The close-up images show the cells arranged as two rows meeting end to end across the module, with laser-welded busbars on a black carrier along the cell tops.

Close-up of the top of an MMA cell module showing welded busbars on a black plastic carrier, a grey insulating sheet over the cell tops with dashed outlines above each cell vent, and thin layers between neighbouring cells.
Top of a cell module: busbars on their carrier, and an insulating sheet with break-out outlines over each cell vent. Image: Mercedes-Benz

Nigel: In the images you can see a foam layer between the large faces of the cells, and between the butting short edges where two cells meet end to end. Is this for cell expansion, or a fire barrier?

Mercedes has not said, so this is our reading. It is very likely both. A compressible pad between the large faces takes up cell swelling over life, and a silicon-oxide anode swells more than plain graphite, so the NMC cells need that allowance. Mercedes also says the spacing between cells and the construction of cells and modules are designed to stop a thermal event spreading [1], and a pad that doubles as a thermal barrier is a common way to do that. The grey sheet over the cell tops looks like a mica-type insulating layer, with the dashed outlines marking where it breaks open above each cell vent so gas can escape into the ducts in the cover [13]. We cannot tell the pad material from photographs; a teardown would settle it.

Side view of an MMA cell module showing two cells meeting end to end with a dark compressible pad between them, and a foam block between the module top and the pack housing.
Side of a module, showing the pad where two cells meet end to end. Image: Mercedes-Benz

Pack and cell size from the press images

Mercedes has not published the outside dimensions of the pack, so we measured them from its plan-view press image of the rolling chassis [15], using the 2,790 mm wheelbase [14] as the scale. One correction matters. Scaling straight from the wheel centres makes the tyres come out at about 700 mm diameter, roughly 6% too big for the sizes fitted. That is perspective: the camera was only about 4 m above the hubs, so the tops of the tyres are closer to the lens and look larger. We fitted a simple pinhole camera model to the tyre outlines in both length and width, which gives 1.38 mm per pixel at hub height. The pack lid sits roughly 100 mm below the hubs, given about 107 mm of ground clearance, so it is further from the camera and needs 2 to 3% more. As a check, the outer tyre faces span the same width front and rear in the image, which fits the staggered 225 front and 255 rear tyres on the display car.

Top-down Mercedes press image of the CLA rolling chassis with the battery pack outlined, annotated with estimated pack length 1,810 mm, width 1,300 mm, cell pitch 33 mm and the 2,790 mm wheelbase used as the scale reference
Our measurement of the pack from the Mercedes plan-view image [15], scaled from the 2,790 mm wheelbase [14] and corrected for camera perspective. Estimates, not published dimensions. Image: Mercedes-Benz, annotations: batterydesign.net

The cut-away corner of the same image shows the cell tops, which lets us size the cells as well. Cell vents repeat every 33 mm along the car. Across the car, the two terminals of one cell are about 214 mm apart with the vent exactly midway between them, and where two cells meet end to end their terminals are about 66 mm apart. That puts each terminal roughly 30 mm in from the end of its cell, and gives a cell about 275 mm long. Height cannot be seen from above, so we worked it back from Mercedes’ figures: 88.9 kWh at 680 Wh/l [1] is about 131 litres of cells, or about 680 ml per cell over 192 cells. Divided by a 275 x 32 mm footprint, that is about 78 mm.

DimensionOur estimateLikely rangeHow we got it
Pack length, lid flange (mm)1,8101,795 to 1,830Plan image, perspective corrected
Pack width, lid flange (mm)1,3001,290 to 1,315Plan image, perspective corrected
Width across mounting tabs (mm)1,3951,375 to 1,415Plan image
Cell pitch (mm)3332 to 34Vent spacing in the cut-away
Cell thickness (mm)3231 to 33Pitch less an assumed 0.5 to 2 mm pad
Cell length (mm)275265 to 285Terminal positions in the cut-away
Cell height, can only (mm)7872 to 85Back-calculated from 680 Wh/l [1]
Pack and cell dimensions estimated from Mercedes press images [13][15] and energy density figures [1]. Our estimates, not published figures.

The numbers hang together. Two modules of 24 cells at 33 mm come to about 1,585 mm, leaving about 225 mm for the end walls, the gap at the cross brace and the electrics at the rear, which matches the 1,810 mm we measured. Across the car, four cell lengths of about 1,100 mm plus the central cable channel and the side walls fit the 1,300 mm width. The cells cover about 72% of the lid footprint, a reasonable figure for bonded modules in a liquid-cooled tray. If the LFP pack uses the same can, as the volume arithmetic in the variants section suggests, 450 Wh/l gives about 306 Wh per cell, or about 96 Ah at 3.2 V. Pack height is the one outside dimension a plan view cannot give.

Both of Mercedes’ cell densities sit at the top of the prismatic cells in our Cell Database (v1.8).

Prismatic cellsCells in databaseMedian (Wh/l)Top 10% from (Wh/l)CLA cell (Wh/l)CLA position
NMC76490595680 [1]About 97th percentile
LFP307349397450 [1]About 98th percentile
LFP, production from 202250387434450 [1]About 90th percentile
Mercedes’ cell-level volumetric energy density claims against prismatic cells in the BatteryDesign.net Cell Database (v1.8). Our analysis.

In the database, 680 Wh/l sits just below CATL’s Qilin cell (692 Wh/l), and 450 Wh/l matches EVE’s 2024 A24 to A27 family (450 to 465 Wh/l). Top-decile figures are credible for CATL in 2025, but Mercedes does not say what volume it divides by, and a can-only volume that leaves out the terminals flatters the number. If the real figure is nearer the median for recent cells, the cells are taller, around 85 to 90 mm. The length and thickness come from the images and would not change. Our estimates are now in the Pack Database, flagged as estimates.

Against the Pack Database

CLA 250+CLA 200Tesla Model 3 LR (2024)Tesla Model 3 LFP (2021)BMW iX3 50 (Neue Klasse)
ChemistryNMCLFPNMCLFPNMC
Cell formatPrismaticPrismaticCylindricalPrismaticCylindrical
Usable / total (kWh)85 / 88.958 / n.p.75 / 7857.5 / 60.1108.7 / 113.4
Nominal voltage (V)700614357346699
Pack mass (kg)496484475477597
Pack Wh/kg179120*164126190
Peak DC (kW)320200250170400
10 to 80% (min)222027n.p.21
CLA packs against comparable packs in the BatteryDesign.net Pack Database (v1.8). Wh/kg is total energy over pack mass. *CLA 200 uses usable energy, as total is not published. n.p. = not published.

On density the CLA NMC pack sits between the Model 3 and the Neue Klasse. BMW gets its extra 6% with large cylindrical cells in a much bigger pack, so the comparison flatters BMW a little; a larger pack spreads the fixed mass of the enclosure and electronics over more cells. The CLA’s advantage over the Model 3 is not density but voltage: twice the pack voltage is what lets it charge at 320 kW where the Model 3 stops at 250 kW. The LFP packs are close on Wh/kg, but the CLA builds its LFP pack from 192 smaller cells at 800V, where Tesla uses 108 larger cells at 400V. More cells and higher voltage cost money, and Mercedes accepts that to keep one pack design across all variants. The full dataset is in our Pack Database.

What is still unknown

  • Pack height, and a teardown check of our length, width and cell size estimates from the press images.
  • Total energy of the LFP pack and the LFP cell capacity.
  • Measured cell dimensions, and whether the NMC and LFP cells share a can size (our volume arithmetic suggests they do).
  • The material and thickness of the pads between cells.
  • A measured charging curve at different starting temperatures, and any road-test curve for the LFP car.

What to take from this

The CLA is not the densest pack in its class, and it does not need to be. Mercedes has built one mechanical pack, one cell count and one module design, then made three energy contents out of it: a chemistry swap for the LFP car and a software limit for the 71 kWh car. Add an 800V bus with a front-loaded charge curve and the result is a car that charges fast and costs less to vary. As second cell suppliers arrive from 2028, that common envelope will matter even more.

References

  1. New cell chemistries with high energy density, fast-charging capability and performance, Mercedes-Benz Media (read in German)
  2. Deep Dive MMA: How Mercedes wants to score points with efficiency with the electric CLA, electrive, 18 November 2024
  3. World premiere of the Mercedes CLA, electrive, 13 March 2025
  4. Mercedes CLA EQ: Neues Grundmodell mit LFP-Batterie bestellbar, ecomento.de, 16 October 2025
  5. Mercedes introduces fourth CLA powertrain variant, electrive, 13 February 2026
  6. Mercedes CLA 250 EQ: 71-kWh-Akku offenbar per Software limitiert, InsideEVs Germany
  7. Mercedes CLA EV can only use 800V DC fast chargers, Carscoops, May 2025, reporting Wards Auto
  8. The Mercedes CLA EV will work with Tesla Superchargers after all, InsideEVs
  9. Mercedes purchases battery cells from Samsung SDI, electrive, 20 April 2026
  10. Mercedes-Benz CLA 200, EV Database
  11. Mercedes CLA: Additional version with 71 kWh battery, heise autos
  12. Mercedes CLA 250+ review: How good is it really?, electrive, 16 April 2026
  13. Mercedes-Benz MMA technology graphics, “Two cell chemistries at a glance” (24C0373_111) and “Modular architecture and two battery types” (24C0373_114), Mercedes-Benz Media
  14. Mercedes-Benz CLA 200 165kW Sport 58kWh specifications, Top Gear (wheelbase 2,790 mm)
  15. Mercedes-Benz MMA rolling chassis, plan view (24C0374_304), Mercedes-Benz Media
  16. US EPA / CARB Application for Certification, Model Year 2027, test group VMBXV00.0ED6 (CLA 250+ with EQ Technology), Certification Summary Information Report, revised 23 April 2026

See also: Mercedes MMA Battery, Mercedes Vision EQXX, 2026 Mercedes-AMG GT 4-door Coupe, 800V Architecture, BMW iX3 Neue Klasse Battery, Cell to Pack, Pack Benchmarking, Key Pack Metrics

Get the next teardown in your inbox

New teardowns, benchmarks and design data from BatteryDesign.net, free by email. Unsubscribe any time.

Leave a Comment