Dielectric immersion cooling for a battery pack is perhaps the ultimate method of controlling cell temperatures.
Dielectric Fluid: an electrically non-conductive liquid that has a very high resistance to electrical breakdown, even at high voltages.
The cells are immersed in a dielectric and the dielectric then flows through a heat exchanger to extract the heat. The dielectric is in direct contact with the cells and busbars and hence thermal barriers are minimised.
This isn’t though a simple solution as the dielectric is just a heat transfer medium and there are lots of parameters to consider.
- Heat transfer from complete cell surface
- Heat transfer from busbars
- Low cell and cell to cell temperature deltas
- High power output
- Faster warmup
- High cost of dielectric
- Heavier system
- Material compatibility tests
- More maintenance
- Cell failure into dielectric could degrade properties of dielectric fluid
- Structural damage to pack could release oil into environment
The heat transfer from the cell surface directly into the coolant medium is a significant advantage, the dielectric fluids tend to have a lower heat capacity and conductivity than water-glycol. This means that the fluid flow path and rate are important design parameters to avoid local static boundary conditions on the surface of the cell.
Single and Two-Phase Dielectric Fluids: two-phase fluids increase the heat transfer by using latent heat of evaporation of the liquid-to-gas phase transition, this does increase the complexity of the design.
The selection of a dielectric fluid is complex and you will need to consider a number of factors for your application. AVL did the high level comparison in a 2020 presentation looking at the realities of dielectric cooling in a series production battery pack :
- more cooling capability allows the battery to be run hotter
- lower internal resistance (DCIR)
- more power
- reduce busbar cross-sectional area as heat is dissipated to dielectric fluid
- extend lifetime with lower temperature gradients
- sensing properties of dielectric fluid to pre-detect electrical breakdown due to particles or water ingress
- contained system without a header tank to remove service requirements
McLaren P1 GTR original battery and upgraded battery are both dielectrically cooled.
McLaren SpeedTail has a very small, energy dense and powerful (5.2 kW/kg) dielectrically cooled battery pack.
Koenigsegg Regera – appears to use the patented dielectric cooling where it cools the busbars at each end of the cells before then flowing the fluid over the main cell body
Patent: WO2022069910A1 
The cooling patent from RIMAC Automobili appears to show the dielectric cooling system for the Koenigsegg Regera. The dielectric enters the module and flows over both ends of the cells before returning over the centre section of the cell and exiting the module.
Mercedes C63 AMG uses dielectric fluid to cool the central section of the cell body.
Kreisel designed a cylindrical cell cooling system design where the main body of the cell is cooled with dielectric fluid.
“Lowest temperature spreads of less than 1°C on pack level avoid early single cell aging”
Note that the coolant does not flow over either end of the cylindrical cell and hence does not cool the busbars.
Working with a number of companies who produce dielectric fluids.
- test results shows 10°C delta between immersion cooling and indirect liquid cooling method on cell surface temperature
- 20°C delta on busbar temperature
- No fire propagation was detected when during nail penetration to a single cell, causing it to undergo thermal runaway.
- Immersion cooled battery modules tested 10% longer life cycle compared to conventional indirect liquid cooled module at -4C/+2C charge/discharge rates.
LION Smart developed a light-weight battery pack with integrated immersive cooling technology using 3M Novec fluids, that can be used in automotive or aviation productions.
The project is EU funded and a part of LIBAT Clean Sky 2 aiming towards climate neutral aviation by 2050.
Other Application Areas
HV Transformers – dielectric cooling has been used for HV power transformers for a very long time and hence this area is a good source of information.
IT datacentres – moving towards dielectric cooling to increase density, reduce hardware failures, minimize water usage and to reduce costs .
- Charlotte Roe, Xuning Feng, Gavin White, Ruihe Li, Huaibin Wang, Xinyu Rui, Cheng Li, Feng Zhang, Volker Null, Michael Parkes, Yatish Patel, Yan Wang, Hewu Wang, Minggao Ouyang, Gregory Offer, Billy Wu, Immersion cooling for lithium-ion batteries – A review, Journal of Power Sources, Volume 525, 2022
- MIVOLT – Liquid Immersion Cooling
- Choosing the Right Fluid for Electronics Cooling: Seven Dimensions of a Decision: An Aid for Thermal Engineers, DSi
- submer – What’s immersion cooling?
- Kreisel Electric – dielectric cooling design for cylindrical cells
- Xing Mobility – Technology
- How to develop battery technologies for large series applications – on the example of immersion cooling, AVL
There are many different options for battery cooling (and heating). These range in capability and complexity from Passive through to Fully Immersed Dielectric.